Enhance Your Career With Available Preparation Guide for NACE-CIP2-001 Exam
Get Special Discount Offer of NACE-CIP2-001 Certification Exam Sample Questions and Answers
NEW QUESTION # 56
Corrosion is the reverse process of
- A. flaking.
- B. hot dipping.
- C. steel manufacturing.
- D. galvanic deterioration.
Answer: C
NEW QUESTION # 57
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Require the Applicator to remove the coating
- B. Ignore the situation
- C. Advise the Owner and write a Non-Conformance report
- D. Stop the job
Answer: A
NEW QUESTION # 58
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. High Voltage DC Pulse Type
- B. High Voltage DC Constant Current
- C. High Voltage AC
- D. Low Voltage Sponge Type
Answer: B
NEW QUESTION # 59
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Suggest to the Owner that the supervisor should be removed from site
- B. Challenge the supervisor's authority
- C. Express a willingness to work with the site team and follow the specification
- D. Defend the previous inspector
Answer: C
NEW QUESTION # 60
An Inspection and Test Plan is required when:
- A. When the Inspector requests one
- B. It is always required
- C. When the Coating Applicator requests one
- D. When the Owner specifies one
Answer: B
NEW QUESTION # 61
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Request clarification from the specifier
- B. Call your supervisor
- C. Enforce the additional requirement
- D. Ignore the additional requirement
Answer: C
NEW QUESTION # 62
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only technical experts would understand
- B. Language that only in the project would understand
- C. Language that another NACE Inspector would understand
- D. Language that the most would understand
Answer: D
NEW QUESTION # 63
Ideally, documentation requirements should be defined:
- A. By the inspector
- B. In the specification
- C. At the pre-job conference
- D. By the contractor
Answer: B
NEW QUESTION # 64
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and submit the reports without any further action
- B. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- C. Correct the errors yourself and suggest the Level 1 inspector be replaced
- D. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
Answer: D
NEW QUESTION # 65
When observing fabrication defects the NACE Inspector should:
- A. Consult the specification to determine how they should be treated
- B. Require they be corrected prior to coating
- C. Stop the job immediately
- D. Write an NCR and call the fabricator
Answer: A
NEW QUESTION # 66
Inspection and Test Plans are provided to:
- A. So the Inspector doesn't have to read the entire specification
- B. So the contractor has a single document to reference
- C. Outline the inspection steps, sequencing and pass/fail criteria
- D. To supersede the requirements of the product data sheets
Answer: C
NEW QUESTION # 67
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Verbally challenge the NCR
- B. Review the NCR with the other Inspector
- C. Consult your supervisor
- D. Request a re-blast of the item in question
Answer: C
NEW QUESTION # 68
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise the other inspector he is using an incorrect method
- B. Advise your QC Manager to change the ITP to the use of the salt smart meter
- C. Redo the pre-cleaning based on the other inspectors results
- D. Review the specification with the other inspector to see what method was specified
Answer: D
NEW QUESTION # 69
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. coatings are expected to degrade over time.
- B. linings protect the contents and the container.
- C. linings are more durable than coatings.
- D. coatings are more durable than linings.
Answer: B
NEW QUESTION # 70
The Inspectors' goal at the Pre-Job Conference is to:
- A. Obtain a clear understanding of the Specification
- B. Discuss contractual requirements
- C. Manage the meeting so it doesn't go off topic
- D. Take accurate meeting minutes for distribution
Answer: A
NEW QUESTION # 71
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION # 72
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Exit the tank and document the incident in your daily report
- B. Don your air supplied respirator and continue the testing
- C. Investigate to find the source of the odor
- D. Exit the tank and immediately and report the problem to the nearest safety supervisor
Answer: D
NEW QUESTION # 73
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. High-pressure water washing
- B. Acid etching
- C. Sacking
- D. Stoning
Answer: C
NEW QUESTION # 74
Non-Conformance Reports are designed to:
- A. Assist the Owner in negotiating credits from the Contractor
- B. Elevate the status of the Inspector
- C. Punish the Contractor for substandard work
- D. To identify items that do not meet the specification requirements
Answer: D
NEW QUESTION # 75
......
Updated NACE-CIP2-001 Dumps Questions Are Available For Passing NACE Exam: https://www.exam4labs.com/NACE-CIP2-001-practice-torrent.html
New NACE-CIP2-001 Dumps For Preparing CIP Level 2 Certified NACE Exam Well: https://drive.google.com/open?id=1ZyeVoGHcO2BSmRWdkWWHnNo0wGcdDXd6