[2024] NACE-CIP2-001 Actual Exam Dumps, NACE-CIP2-001 Practice Test
Exam4Labs NACE-CIP2-001 dumps & CIP Level 2 sure practice dumps
NEW QUESTION # 41
Examples of non-ferrous metals include
Select All that Apply:
- A. aluminum
- B. copper
- C. iron
- D. mild steel.
Answer: A,B
NEW QUESTION # 42
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. Another NACE Level 2 Inspector
- B. A NACE Level 1 Inspector
- C. A NACE Level 3 Inspector
- D. A NACE Protective Coating Specialist
Answer: C
NEW QUESTION # 43
Pre-cleaning of work pieces will NOT remove
- A. dirt.
- B. snow, ice or water.
- C. mill scale.
- D. oil or grease.
Answer: C
NEW QUESTION # 44
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise your QC Manager to change the ITP to the use of the salt smart meter
- B. Advise the other inspector he is using an incorrect method
- C. Review the specification with the other inspector to see what method was specified
- D. Redo the pre-cleaning based on the other inspectors results
Answer: C
NEW QUESTION # 45
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
- B. Ensure the glue on the dolly is properly applied prior to use
- C. Consult SSPC Guide 1 prior to use
- D. Determine the Dry Film Thickness of the coating prior to use
Answer: D
NEW QUESTION # 46
Coating surveys may include which steps?
Select All That Apply:
- A. Summarize the collected data
- B. Evaluate the coatings performance
- C. Schedule the remedial work
- D. Develop a survey plan
Answer: A,B,C,D
NEW QUESTION # 47
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Coal Tar Enamel
- B. 2-Layer Polyethylene (PE)
- C. 3-Layer Polyethylene (PE)
- D. Fusion Bonded Epoxy
Answer: C
NEW QUESTION # 48
Surface preparation of concrete is performed using:
- A. Methods that have been modified for concrete
- B. Methods that are exactly the same as steel
- C. Methods that are completely different to steel
- D. Methods that are the same as wood
Answer: A
NEW QUESTION # 49
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Request clarification from the specifier
- B. Ignore the additional requirement
- C. Enforce the additional requirement
- D. Call your supervisor
Answer: C
NEW QUESTION # 50
When observing fabrication defects the NACE Inspector should:
- A. Require they be corrected prior to coating
- B. Consult the specification to determine how they should be treated
- C. Write an NCR and call the fabricator
- D. Stop the job immediately
Answer: B
NEW QUESTION # 51
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Give them as much advance notice as possible about upcoming changes
- B. Implement immediate to get them motivated
- C. Make sure they are the center of attention in all site meetings
- D. Challenge their value to the team and try to get them out of their comfort zone
Answer: A
NEW QUESTION # 52
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Gel stage
- D. Wetting stage
Answer: B
NEW QUESTION # 53
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Move the nozzle quicker
- B. a), b) and c)
- C. Lower the blast pressure
- D. Increase the standoff distance
Answer: B
NEW QUESTION # 54
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Verbally challenge the NCR
- B. Consult your supervisor
- C. Review the NCR with the other Inspector
- D. Request a re-blast of the item in question
Answer: B
NEW QUESTION # 55
When observing design defects the NACE Inspector should:
- A. Ignore the defect as the inspector can't change the design
- B. Request that the item be rebuilt with a better design for coating
- C. Document the defect and the potential problems that could result
- D. Stop the job immediately
Answer: C
NEW QUESTION # 56
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A set of 14 pencils of varying hardness
- B. A destructive paint inspection Tooke gauge
- C. A hardness tester
- D. A mechanical adhesion tester
Answer: B
NEW QUESTION # 57
NACE No.13/ SSPC 6 identifies the use of:
- A. Steam cleaning only
- B. Abrasive blasting only
- C. Various methods of cleaning
- D. Watterjetting only
Answer: C
NEW QUESTION # 58
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. De facto
- B. Mandatory
- C. Consensus
- D. Voluntary
Answer: D
NEW QUESTION # 59
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Ultra Sonic DFT Gauge
- B. Eddy Current Gauge
- C. Tooke Gauge
- D. Magnetic Gauge
Answer: C
NEW QUESTION # 60
NACE Standards include:
- A. a) only
- B. Standard Practices
- C. a) & b)
- D. Material Requirements
Answer: C
NEW QUESTION # 61
The Inspectors' goal at the Pre-Job Conference is to:
- A. Discuss contractual requirements
- B. Manage the meeting so it doesn't go off topic
- C. Obtain a clear understanding of the Specification
- D. Take accurate meeting minutes for distribution
Answer: C
NEW QUESTION # 62
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and submit the reports without any further action
- B. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
- C. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- D. Correct the errors yourself and suggest the Level 1 inspector be replaced
Answer: B
NEW QUESTION # 63
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cohesion failure
- B. Adhesion failure
- C. Cold flow or creep
- D. Glue failure
Answer: C
NEW QUESTION # 64
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 35 single rubs with a saturated cloth.
- B. 25 single rubs with a saturated cloth.
- C. 50 double rubs with a saturated cloth.
- D. 25 double rubs with a saturated cloth.
Answer: C
NEW QUESTION # 65
......
NACE-CIP2-001 Actual Questions and Braindumps: https://www.exam4labs.com/NACE-CIP2-001-practice-torrent.html
Pass NACE-CIP2-001 Exam with Updated NACE-CIP2-001 Exam Dumps PDF 2024: https://drive.google.com/open?id=1ZyeVoGHcO2BSmRWdkWWHnNo0wGcdDXd6