Unique Top-selling CQE Exams - New 2021 ASQ Pratice Exam
ASQ Certification Dumps CQE Exam for Full Questions - Exam Study Guide
NEW QUESTION 42
The Shewhart or Deming cycle is often referred to as
- A. The cause and effect diagram.
- B. Plan-do-check-act.
- C. The affinity diagram.
- D. Problem solving flow chart.
Answer: B
Explanation:
Explanation
NEW QUESTION 43
The primary reason that nonconforming material should be identified and segregated is
- A. So that responsibility can be determined and disciplinary action taken.
- B. So that the cause of nonconformity can be determined.
- C. So it cannot be used in production without proper authorization.
- D. To obtain samples of poor workmanship for use in the company's training program.
Answer: C
NEW QUESTION 44
A two-way analysis of variance has r levels for one variable and c levels for the second variable with 2 observations per cell. The degree of freedom for interaction is
- A. (r-1)(c-1)
- B. 2(r-1)(c-1)
- C. 2(r)(c)
- D. rc-1
Answer: A
NEW QUESTION 45
The primary reason that nonconforming material should be identified and segregated is
- A. So that responsibility can be determined and disciplinary action taken.
- B. So that the cause of nonconformity can be determined.
- C. So it cannot be used in production without proper authorization.
- D. To obtain samples of poor workmanship for use in the company's training program.
Answer: C
NEW QUESTION 46
Benchmarking might be defined as any of the following EXCEPT:
- A. A process for rigorously measuring your performance versus the best-in-class companies.
- B. Comparing the performance of one company to a set of standards and then to another'sperformance.
- C. The search for best industry practices that lead to superior performance.
- D. A standard of excellence or achievement against which other similar things must be measured orjudged.
Answer: B
NEW QUESTION 47
The design function which assigns probability of failures between components or subsystems is called
- A. Qualification.
- B. Confidence.
- C. Significance
- D. Apportionment.
Answer: D
NEW QUESTION 48
If a sample size of 16 yields an average of 12 and standard deviation of 3, estimate the 95% confidence interval for the population (assume a normal distribution).
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: A
NEW QUESTION 49
Which of the following statements BEST describes a bimodal distribution?
- A. This distribution shows stratified data and two distinct peaks.
- B. This distribution has several distribution peaks.
- C. This distribution is truncated.
- D. This distribution shows a single mode and bell shaped distribution.
Answer: A
NEW QUESTION 50
An X-bar and R chart with n=5 has been plotted for some time and has demonstrated random variation. Upon review of the last 30 plot points, the expected number of runs around the centerline on the X-bar chart is expected to be approximately which of the following?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 51
What order do the following corrective action steps normally take for nonconforming product?
. Analyze the problem.
. Assign responsibility.
. Take preventive action.
. Evaluate potential importance.
. Investigate possible causes.
- A. V,II,IV,I,III
- B. II,I,IV, V,III
- C. I,II,V,IV,III
- D. II,IV, V,I,III
Answer: D
NEW QUESTION 52
A product failure in the customer's hands is bad for the company. Why do only 4% of the customers normally file a complaint?
- A. A warranty is in place on the product.
- B. The product guarantee takes care of the product.
- C. They don't think it will do any good.
- D. It is a minor inconvenience.
Answer: C
NEW QUESTION 53
Which of the following control charts are more efficient than an X-bar chart at detecting small shifts in the mean?
I. CUSUM.
II. EWQR.
III. EWMA.
- A. I and III only
- B. II only
- C. III only
- D. I only
Answer: A
NEW QUESTION 54
What is the standard deviation of the values below?
4.5, 5.1, 6.2, 2.1, 3.9
- A. 1.362
- B. 1.522
- C. 1.136
- D. 2.087
Answer: A
NEW QUESTION 55
To be effective, a corrective and preventive action system must have
- A. Approved of the QC department.
- B. A material review board.
- C. A method for identifying nonconformities.
- D. Top management support.
Answer: C
NEW QUESTION 56
Given the following probabilities
1 or more defects = .70
2 or more defects = .35
3 or more defects = .15
4 or more defects = .03
What is the probability of 2 or fewer defects?
- A. 0.20
- B. 0.35
- C. 0.65
- D. 0.85
Answer: D
NEW QUESTION 57
Which of the following are TRUE statements regarding the use of visual inspection?
I. Reference standards can be used.
II. It provides consistency between inspectors.
III. It is relatively expensive.
IV. It can be quickly performed.
- A. I and IV only
- B. I, II, III and IV
- C. II and IV only
- D. I, II and IV only
Answer: A
NEW QUESTION 58
What is the highest form of partnering with employees?
- A. Task teams.
- B. Stock option plans.
- C. Employee involvement.
- D. Cost reduction projects.
Answer: C
NEW QUESTION 59
Writing and establishing process control procedures is
- A. Preventive action.
- B. Corrective action.
- C. Disposition.
- D. Notification.
Answer: A
NEW QUESTION 60
......
Best way to practice test for ASQ CQE: https://www.exam4labs.com/CQE-practice-torrent.html
CQE Dump Ready - Exam Questions and Answers: https://drive.google.com/open?id=1Fb8KcTFRX_yz5kI81TwhHEvmzn82ixZA